Brand new The Magpul Bipod for 1913 Picatinny Rail offers serious strength and versatility at a price that provides unmatched value. Rich with important features, our lightweight Mil-spec hard anodized 6061 T-6 aluminum and injection-molded polymer bipod brings innovation in ergonomics, functionality, strength and value together. An aesthetically pleasing, low-profile design conceals its mechanisms and hardware, smoothly brushing off snags and bumps. Optimized for rapid one-handed adjustments, the bipod quickly and quietly transitions between countless user configurations. The Magpul Bipod includes many features normally found on bipods at a significantly higher cost. The Magpul Bipod is exceptionally strong and built to perform under punishing field conditions.   Like all Magpul products, the Bipod is constructed of rugged, high-strength materials and designed to last a lifetime. In the shooting position, it is easily loaded with stabilizing forward tension without fear of failure or warping. Mil-spec hard anodized 6061 T-6 aluminum, stainless steel internals, and injection-molded reinforced polymer ensure years of dependable performance and reliability, all while shaving weight. At just over 11 oz., the Magpul Bipod is lighter than many pricier bipods currently on the market. Deploying and adjusting the Magpul Bipod is quick and easy. Spring-tensioned legs stow neatly forward and snap down and lock into place with one hand. Leg extensions slide and lock securely with the push of a button on any of the seven half-inch spaced locking detents. The legs extend a full four inches, from 6.3” to 10.3”.  An industry-exclusive 50° of total tilt and 40° of total pan are controlled by a glove-friendly knurled tool-less bipod locking knob located between the extended legs, allowing easy adjustment between shots. Additionally, the Magpul Bipod has the exclusive ability to lock pan at 0° while maintaining full tilt functionality. From the drawing board, the Magpul Bipod was designed to be barely noticed until needed. Folded, the streamlined housing and legs fit neatly under the barrel and are just under 2.3” deep and 3.3” wide. In addition, anodized surfaces and tight, precision tolerances mitigate squeaks and rattles. The Magpul Bipod has many features that are also useful even when it is in the stowed position. A soft rubber bipod locking knob cap is attached to the locking knob gives users a steady, non-marring forward rest while the bipod is folded. Additionally, its staggered soft rubber feet hold fast on a variety of shooting surfaces and are easily removed with a roll pin punch. Should users choose to change feet, the Magpul Bipod’s legs accept most Atlas pattern bipod replaceable feet, except for the Atlas 5-H style. Made in USA

categories:Sporting GoodsGuns

2745 impressions

407 views

Brand new Manufacturer: Pro Mag Fits: AR15 Caliber: 7.62x39 Capacity: 5/30 Rounds Body Material: Metal Follower Material: Polymer Made in USA

categories:Sporting GoodsGuns

5007 impressions

614 views

Brand new Manufacturer: Pro Mag Fits: FN P90/PS90   Caliber: 5.7*28 Capacity: 5/50 Rounds Material: Polymer and Steel Made in USA

categories:Sporting GoodsGuns

1524 impressions

423 views

Brand new The MOE Grip (Magpul Original Equipment) is a drop-in upgrade for the standard AR15 / M4 pistol grip. The ergonomic, hand-filling design combines anti-slip texturing with storage core capability. With a similar shape to a ‘medium’ sized MIAD, the one-piece reinforced polymer construction provides simplicity and a reduced cost while still maintaining the durability needed to withstand operational environments. The MOE Grip accepts optional Storage Cores for gear stowage and includes a basic grip cap. All mounting hardware included. Positive Anti-Slip Texture Beavertail Backstrap For Enhanced Ergonomics Storage Core Capability Hard Polymer Bottom Made in USA

categories:Sporting GoodsGuns

2338 impressions

362 views

Brand new The Magpul X-22 Backpacker stock takes the function of our full-size Hunter X-22 Takedown, and pares it down for ease of storage and transportation. Made for the Ruger 10/22 Takedown rifle, the X-22 Backpacker offers a minimalist solution for the hunter or outdoorsman who wants to transport their rifle in an efficient, convenient package without compromising shooting performance. Constructed of a durable advanced polymer, the X-22 Backpacker features an ergonomic hand guard, optional QD sling mounting capability, integrated storage compartment in the grip, a hinged storage compartment in the stock capable of storing up to 3 spare 10rd magazines, a MOE SL non-slip rubber butt pad, and a unique locking interface to attach the barrel assembly to the receiver when being transported. Fits all Ruger 10/22 Takedown rifles as well as the Tactical Solutions SBX barrel. Drop-in design compatible with all factory Ruger 10/22 Takedown Unique locking interface to attach the barrel assembly to the stock body when being transported Reinforced polymer construction for strength and durability Ergonomic hand guard Comes with interchangeable standard and ‚ optic height‚ cheek risers Optional QD sling mounting capability Integrated storage compartment in the grip Hinged storage compartment in the stock capable of storing up to 3 spare 10rd magazines MOE SL nonslip rubber butt pad Made in USA

categories:Sporting GoodsGuns

17384 impressions

1270 views

Brand new Caliber: .223 REM Capacity: 5 Material: Polymer Made in CZ

categories:Sporting GoodsGuns

9546 impressions

415 views

Brand new Manufacturer: Pro Mag Fits: Enfield #1 Mark III Caliber: .303 British Capacity: 10 Rounds Material: Steel and Polymer Made in USA

categories:Sporting GoodsGuns

6499 impressions

554 views

Brand new The Magpul Bipod for 1913 Picatinny Rail offers serious strength and versatility at a price that provides unmatched value. Rich with important features, our lightweight Mil-spec hard anodized 6061 T-6 aluminum and injection-molded polymer bipod brings innovation in ergonomics, functionality, strength and value together. An aesthetically pleasing, low-profile design conceals its mechanisms and hardware, smoothly brushing off snags and bumps. Optimized for rapid one-handed adjustments, the bipod quickly and quietly transitions between countless user configurations. The Magpul Bipod includes many features normally found on bipods at a significantly higher cost. The Magpul Bipod is exceptionally strong and built to perform under punishing field conditions.   Like all Magpul products, the Bipod is constructed of rugged, high-strength materials and designed to last a lifetime. In the shooting position, it is easily loaded with stabilizing forward tension without fear of failure or warping. Mil-spec hard anodized 6061 T-6 aluminum, stainless steel internals, and injection-molded reinforced polymer ensure years of dependable performance and reliability, all while shaving weight. At just over 11 oz., the Magpul Bipod is lighter than many pricier bipods currently on the market. Deploying and adjusting the Magpul Bipod is quick and easy. Spring-tensioned legs stow neatly forward and snap down and lock into place with one hand. Leg extensions slide and lock securely with the push of a button on any of the seven half-inch spaced locking detents. The legs extend a full four inches, from 6.3” to 10.3”.  An industry-exclusive 50° of total tilt and 40° of total pan are controlled by a glove-friendly knurled tool-less bipod locking knob located between the extended legs, allowing easy adjustment between shots. Additionally, the Magpul Bipod has the exclusive ability to lock pan at 0° while maintaining full tilt functionality. From the drawing board, the Magpul Bipod was designed to be barely noticed until needed. Folded, the streamlined housing and legs fit neatly under the barrel and are just under 2.3” deep and 3.3” wide. In addition, anodized surfaces and tight, precision tolerances mitigate squeaks and rattles. The Magpul Bipod has many features that are also useful even when it is in the stowed position. A soft rubber bipod locking knob cap is attached to the locking knob gives users a steady, non-marring forward rest while the bipod is folded. Additionally, its staggered soft rubber feet hold fast on a variety of shooting surfaces and are easily removed with a roll pin punch. Should users choose to change feet, the Magpul Bipod’s legs accept most Atlas pattern bipod replaceable feet, except for the Atlas 5-H style. Made in USA

categories:Sporting GoodsGuns

2777 impressions

492 views

Brand new Caliber: .22 LR Capacity: 20 Rounds Material: Polymer

categories:Sporting GoodsGuns

6677 impressions

567 views

Brand new Compatible with short action AICS (Accuracy International Chassis Systems) pattern bottom metal and cartridges built on a 0.470" case head such as 7.62x51/.308 Winchester, 7mm-08 Remington, 6.5mm Creedmoor, .260 Remington, .243 Winchester, and others Accepts a cartridge overall length of up to 2.86" Next-generation impact and crush resistant polymer construction Self-lubricating follower for increased reliability Long life stainless steel spring Paint pen dot matrix panels on the bottom of the body to allow for identification marking Flared floorplate aids magazine handling and is easy to disassemble for maintenance NOTE:  Not compatible with smaller base diameter cartridges such as .220 Swift, .223 Remington, .300 AAC Blackout, etc. or larger short action magnums. In addition, due to the wide variety and potential combinations of aftermarket receivers, stocks, chassis, and bottom metal that accept AICS pattern mags, minor fitting may be required. Not compatible with Accuracy International AE rifles or semi-auto platforms utilizing SR25/M110 pattern magazines.

categories:Sporting GoodsGuns

33029 impressions

732 views

Brand new The KRISS Vector Ambidextrous Folding Stock is the dedicated folding stock solution for the Vector Gen 2.1 (Gen II 2017). The stock is constructed of aluminum and advanced polymer composites. The KRISS Vector Ambidextrous Folding Stock secures to the upper assembly with a push button hinge that can be configured to fold to the right or the left. The stock features two QD sling swivel mounts on the left and right side, as well as a sling loop towards the rear. In addition to folding, this stock is also adjustable for length of pull, adjusting to three positions. One end of the stock is installed directly into the Gen 2.1 Vector's upper housing. The other end is the stock itself. It is not an adapter.

categories:Sporting GoodsGuns

3314 impressions

507 views

Brand new Designed for use with all M-LOK compatible Hand Guards and Forends M-LOK Aluminum Rail Sections allow the attachment of various 1913 Picatinny spec rail-mounted accessories such as lights, vertical grips, etc. Machined from milspec-anodized aluminum, M-LOK Rail Sections also feature beveled ends to reduce snagging and eliminate sharp corners and edges. All hardware necessary for attachment directly to M-LOK Slots on either aluminum or polymer hand guards and forends is included. 7 Slots Max overall length of 3.3″.

categories:Sporting GoodsGuns

1534 impressions

319 views

Please text anytime 6476871484. New in original case. No PAL required. Non-lethal self-defense semiautomatic 5 round handgun have been vetted by Government Agencies, Police Forces and Private Security Agencies worldwide. Comes with: 1. Carrying case. 2. Spare 5 round magazine. 3. 12g Co2 power cartridges x 2 4. 5 training powder , 5 plastic , 5 eco-kinetic, 5 rubber and 5 full metal bullets. 25 projectiles total included. This Gun is a non-lethal self-defense weapon that uses compressed CO2 to fire projectiles at high velocity. The LE (Law Enforcement ) model shoots .68 caliber round kinetic and chemical irritant projectiles ( only inert powder can be legally used in Canada) that can disable a threat from up to 80-feet away. The projectiles can be rubber-steel, plastic , inert powder, or kinetic impact aluminum projectiles, depending on the situation. The .68 caliber projectiles can be filled with a powerful chemical irritant that bursts upon impact and disperses a cloud of powerful pepper and tear gas powder (Not in Canada). The LE version is manufactured using glass-reinforced polymers and aircraft grade aluminum.

categories:Sporting GoodsGuns

13139 impressions

2155 views

Brand new Designed for use with all M-LOK compatible Hand Guards and Forends M-LOK Aluminum Rail Sections allow the attachment of various 1913 Picatinny spec rail-mounted accessories such as lights, vertical grips, etc. Machined from milspec-anodized aluminum, M-LOK Rail Sections also feature beveled ends to reduce snagging and eliminate sharp corners and edges. All hardware necessary for attachment directly to M-LOK Slots on either aluminum or polymer hand guards and forends is included. 3 Slots Max overall length of 1.6″.

categories:Sporting GoodsGuns

1997 impressions

399 views

Brand new The Magpul M-LOK AFG (Angled Fore Grip) is the result of research and refinements done to the original AFG and AFG-2. By integrating the direct-attach M-LOK mounting system with minimalist construction we were able to produce a high strength grip that only weighs 1.2 ounces, including hardware. Allowing for a wider range of mounting location options, the M-LOK AFG is ¾" shorter than the AFG-2 while maintaining a similar gripping surface area. Even though the M-LOK AFG is more compact than its predecessors it continues to take into account natural body mechanics to provide a comfortable and stable user interface that reduces fatigue and allows for more precise weapon control. By positioning the shooter's hand high on the centerline of the bore, unlike conventional vertical fore grips, the M-LOK AFG helps mitigate recoil and control the weapon to facilitate faster, more accurate follow-up shots. All hardware necessary for attachment directly to M-LOK Slots on either aluminum or polymer hand guards and forends is included. Made in USA

categories:Sporting GoodsGuns

2277 impressions

395 views

Brand new Five-Position Forend Pistol Grip Ergonomic Design Textured Grip Gives You Extra Support & Stability When Shooting Installs Onto a Standard Picatinny Rail (Not Included) DuPont Extreme Temperature Glass Reinforced Polymer Matte Black Fits: Standard Picatinny rails Limited Lifetime Warranty Made in USA

categories:Sporting GoodsGuns

2446 impressions

454 views

CVA Scout VE SS-Black, single shot, break open 44 Mag Rifle, CR4431S Condition : new Tax rates shipping into your province NB, PEI, NS, NL, all pay 15% Ont, pays 13% Everybody else pays 5% GST only contact john at Doctor Deals 506-855-5377 e-transfer only Shipping through Canada Post, 18+ Signature For the hunter who wants a high-quality single shot rifle, the SCOUT is the ideal choice. Its sleek, lightweight, and easy to operate design sets a new standard for affordable single shot hunting rifles. Every stock is lightweight, 100% ambidextrous, and features CVA’s CrushZone® Recoil pad – a real plus for heavier calibers. The SCOUT .44 Magnum comes with a 22” fluted stainless steel barrel. Featuring quick-take-down, tools-free disassembly, it’s also a great stowaway emergency/survival gun for the camp, boat, or truck. Plus, all SCOUT rifles feature a genuine DuraSight® scope rail Features & Specifications Model : Scout VE SS-Black Caliber : 44 Magnum Capacity : 1 Barrel Length : 22″ Barrel Type : fluted stainless steel Stock : Black Polymer Butt Pad : Rubber Action : Break open Sight : DuraSight scope rail only

categories:Sporting GoodsGuns

10681 impressions

1047 views

Brand new The MVG is a light weight, inexpensive vertical foregrip that attaches directly to M-LOK compatible hand guards and forends with no additional Picatinny rails required. Made from the same high quality polymer as other Magpul products, the M-LOK MVG uses the new Magpul TSP texture for positive control in all environments.  With rounded contours and a shorter length, it has been optimized for use with the "thumb break method" of shooting and can also be used as a traditional vertical foregrip. All hardware necessary for attachment directly to M-LOK Slots on either aluminum or polymer hand guards and forends is included. Made in USA

categories:Guns

2599 impressions

382 views

Brand new All steel construction Steel, rectangular sight post selectable between Match and Standard widths   —.040” Match width for increased precision   —.060” Standard width for maximum visibility Case hardened and finished with Melonite QPQ™ for extreme resistance to wear and corrosion Mounts on any MIL-STD-1913 Picatinny/STANAG 4694 rail including receiver-height gas blocks Elevation adjustment knob – no tools required Positive detents in both the up and down positions as well as on the elevation knob Standard AR height over bore when deployed, 45 deg. offset right-hand side NOTE:  All MBUS Pro Front Sights now come factory-equipped with the Enhanced Front Sight Post. There is no need to order one separately unless you are retrofitting an older MBUS Pro front sight. Enhanced Front Site Posts are not compatible with standard MBUS polymer sights. Only compatible with MBUS Pro OFFSET Rear sight MAG526.

categories:Guns

2778 impressions

410 views

Brand new Designed for use with all M-LOK compatible Hand Guards and Forends M-LOK Aluminum Rail Sections allow the attachment of various 1913 Picatinny spec rail-mounted accessories such as lights, vertical grips, etc. Machined from milspec-anodized aluminum, M-LOK Rail Sections also feature beveled ends to reduce snagging and eliminate sharp corners and edges. All hardware necessary for attachment directly to M-LOK Slots on either aluminum or polymer hand guards and forends is included. 9 Slots Max overall length of 4.1″.

categories:Guns

2063 impressions

345 views

Brand new Can be Fired in Opened or Folded Position Quick Release Button Allows Stock to Lock in Folded/Unfolded Position Textured Pistol Grip Ambidextrous Pre-Drilled to Accept Shotgun Shell Holder Easy Installation Sling Swivel Stud Included DuPont® Extreme Temperature Glass Reinforced Polymer Stock Limited Lifetime Warranty Made in USA Fits Most 12 GA Maverick 88, Mossberg 500/535/590/835, Remington 870 and Winchester 1200/1300 Shotguns

categories:Guns

13659 impressions

718 views